![]() The added rings really help add some dimension to the goggles, and the nuts are the icing on the cake.įrom here, they are ready to be linked to each other. At this point, its ready for the final coat of paint.Ī few coats of metallic spray paint, I hot glued the nuts on. I sanded that down the small parts out of habit to see if I could smooth things out a little more, nothing too extensive. I had a little left over from the helmet and it needed to be used. From here I sprayed a primer to give a base coat, also completely optional. What didn’t come off I used a utility knife to cut them out. Once all the segments were cut, I cleaned up the edges with the belt sander to get rid of the random bits and to smooth the edges down. This would be helpful for the piping as well, not just the accents. My suggestion would be to clamp them down and/or use a miter guide like any of these. This was the hard part slicing cleanly and straight. Since it is designed to fit snuggly, I sliced out pieces roughly the width of the nuts (or bolts on the sides of the real ones seen here). So I just made my own □ I needed something that would fit snuggly to the outside of the pipe that I cut so I used a coupling, or a female to female joint. Neither from what I know, nor from what I could find. The problem I found was, as far as I am aware of, there are no pre-made pieces of PVC that look like the example she showed in her video. The girls goggles had a raised rim around the outside of the goggles. I probably still have enough pipe for another 6 or so if I pushed it.įor the coupling, this is completely optional. I figured I was making a couple pairs and I had enough materials for more, so I made 4 in the end. Repeat for any additional set you decide to make. This way the angle for the second goggle matches the first cut. Again, personal preference.įrom there, it’s basically just hack away at the pipe until all your parts are cut out, making the first cut at an angle and the second straight across. Since cut at an angle, on the longer side, I made one set close to 2 inches long and the shortest set about 1.5 inches. I chose the length of the goggles randomly as well. ![]() In the end it was perfect, but again, up to you and the contour of your own face. I didn’t choose anything specific degree, but more so just made a choice willy nilly. I thought this was a good idea so I followed that model. In one video I watched the girl had made hers out of the same material and had them cut at an angle to fit your face better. The first thing I did was cut up sections of the 2 inch PVC pipe for the main section of the eye pieces using the hack saw. Thread and needle – not necessary but very helpfulģ inches of generic jewerly metal – or twist tie, or any small wire should work too Here are the materials I used and how I put it together.Ģ-inch PVC pipe segment – I used a precut section about 2 feet longġ female to female joining piece of PVC – color doesn’t matter From there you can make a collection of pointers that make the best costume that fits you. My suggestion would be to scour the interwebs for the version you are most comfortable with, or by what works best depending on your timeline. Although, the majority of the video is of the girl bouncing around than actual instruction, you can still find good pointers for the costume. There are a good amount of people out there with DIY minion goggles of their own using all sorts of materials ending up with all sorts of solutions, such as this. After watching the videos online and seeing how people were going about creating theirs, I figured it would be pretty easy to make and would only take about a day. So naturally, I wanted to help out and make them. I’m sure you can buy some cheap plastic ones online somewhere, but that just takes all the fun out of it. The costume for the most part is relatively easy to piece together from thrift shops and what not, with the exception of the goggles. For Halloween this year my girlfriend and her friend decided to be Despicable Me minions.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |